Machined parts for robotics and automation

Joint housings, gripper parts and frames for automation builders, often in small series with several revisions. Made in our audited network in Bursa, to your drawing.

Email a drawing
Milled aluminium bearing housing with a flanged bearing, a turned shaft and four socket-head screws
IndustryRobotics & automation
Typical partsJoint housings, gripper parts, frames
MaterialsAl 6061 / 7075, C45, 42CrMo4, 1.4301
Key requirementsBearing seats, low weight, revisions between batches
Contactsales@ertas.engineering

Parts we quote for automation builders

Typical parts and what the drawing usually asks for. Your drawing decides; this is where we usually start.

PartTypical materialProcessWhat the drawing usually asks for
Joint and gearbox housingsAl 6061 / 7075CNC milling 3/5-axis, CNC turningBearing seats and their position to each other, thin walls after pocketing, anodizing
Gripper parts and fingersAl 7075, C45CNC millingSame geometry across the series, clean contact faces, burr-free edges
Shafts, pins and bushesC45, 42CrMo4, 1.4301CNC turningFits per ISO 286, thread quality, surface finish on bearing seats
Frames and base platesSteel, 1.4301, Al 6061Welded assemblies, CNC millingFlat, square mounting faces machined after welding, hole patterns to the drawing
Covers and guardsAl sheet, 1.4301 sheetSheet metalBurr-free edges, consistent finish, fit to the frame
Small series with revisionsMixed, per drawingAll of the aboveRevision index matched to the order, measurement report for the features you mark

Materials: EN AW-6061/7075, C45, 42CrMo4, stainless 1.4301.

What we check before parts leave

The points automation drawings usually call out, checked against your drawing.

  1. Bearing seats and boresDiameters and positions of bearing seats measured, and reported when the drawing calls them critical features.
  2. Thin walls after pocketingWall thickness on lightweight housings checked against the drawing after the pockets are cut.
  3. The right revisionThe drawing revision on the order is matched to the parts before they ship, so a changed batch does not arrive with old geometry.
  4. Burr-free and cleanEdges, bores and threads checked for burrs and chips. Parts leave clean and packed.
  5. Material on paperMaterial documented to EN 10204 3.1 and matched to the grade on your drawing.
  6. Critical dimensionsA measurement report for the features you mark, delivered with the parts.

Guides

Short references we use ourselves when reviewing a drawing.

Machined components for robotics and automation in small seriesGuide
Aluminium alloys for CNC machining: 6061, 6082, 7075Guide
ISO 286 fits and IT grades: H7/g6 explainedGuide

Other industries

Same network, same documents, different drawings.

Industrial & special machineryPlates, housings, frames, welded basesAutomotive & commercial vehiclesLow- and mid-volume parts, fixtures and gaugesAgricultural & construction machineryWelded frames, brackets, pins, hydraulic blocksEnergy & electrical equipmentCopper busbars, enclosures, machined bracketsHydraulics & fluid powerManifolds, valve blocks, turned partsPhotonics & lasersHousings, mounts, baseplates, cooling platesVacuum & semiconductor equipmentChambers, flanges, fixtures (non-litho)Research, cryogenics & quantumCryostat and beamline partsTest, measurement & labInstrument frames and precision partsData-center cooling & powerWelded manifolds, frames, enclosures

Send the drawing

Attach the drawing, the quantity and the revision. You get a route, a price and a lead time back.

SupplierErtaş Engineering
IndustryRobotics & automation
SendDrawing, quantity, revision
Contactsales@ertas.engineering